How to Build a High Pressure Valve Package for Back Pressure in 14 Steps

When you purchase a High Pressure Control Valve for a back pressure application, you need several other components to make that valve fully functional.

When you order from us, we’ll help you spec in your package and it’ll be delivered fully assembled and ready to install. However, if you purchase these parts individually, you’ll want to know what they do and how to assemble the package.  

In the video above, Kyle shows you how to assemble a high pressure valve package for back pressure regulation. You can also use this guide to help you build your package.

Before you get started, you’ll want to put on your appropriate PPE and be sure to follow all of your company’s safety requirements. 

Parts of a High Pressure Control Valve Package

The components of a high pressure control valve package include: 

  • The valve 
  • A sense line protector to block out the sensed pressure to a device when it exceeds the adjustable limit
  • A drip pot to knock out any liquid in your supply gas
  • A supply gas regulator to provide supply pressure to the pilot
  • A pilot, which is responsible for telling the valve what to do

Components Needed

  • Depending on how you choose to arrange the components, the number of elbow and straight connectors will vary, but you’ll need at least eight, ¼” x 3/8” tubing connectors 
  • Two, ¼” nipples 
  • One, high pressure, ¼” Tconnector  
  • Approximately 5 feet of 3/8” tubing 
  • Loctite 

Tools Needed

Finally, to put the package together, you’ll need the following tools: 

  • A vise 
  • Tubing benders 
  • Tubing cutters 
  •  A ½” wrench 
  • A 5/8” wrench 
  • A 11/16” wrench 
  • A 9/16” wrench (for bonnet bolts) 
  • Channel locks 
  • And a crescent wrench 

If you assemble these packages regularly, you will already have a standard for how to arrange your assembly—whether all of the parts on one side or if it’s more symmetrical. Knowing this in advance makes it easier to attach the tubing connecters and nipples to the parts before adding them each to the valve.   

The way that Kyle builds this package will have the components closer together, facing the front of the valve and on the upstream side. We use less tubing this way and avoid creating areas where someone may try to use to lift. From our experiencethis arrangement is typically most successful 

Arrangements of High Pressure Control Valve Packages

How to Build a High Pressure Control Valve Package for Back Pressure in 14 Steps

  1. Thread the needle valve into the bottom of the drip pot.
  2. Connect the supply gas regulator to the drip pot with a ¼” nipple and Loctite.
  3. Mount the valve body in a vise.
  4. Back pressure valves need to be fail open (pressure close). All of our Kimray valves come standard as fail close, so if you’re building a back pressure package yourself, you’ll need to flip the top works before you begin. See our video if you need help with that process. 
  5. Remove a bolt from the bonnet on the upstream side and attach the drip pot and supply gas regulator on the valve.  
  6. Now we’ll install the pilot to the front of the valve by removing two bonnet bolts, and attaching the bracket included on the pilot. 
  7. Next, install a nipple into the outlet of the sense line protector with Loctite. Connect that into the sensing port of the pilot. Attach the ¼” T into the sense line protector inlet.  
  8. Install one tubing connector into the T, and another into the upstream side of the valve body. 
  9. Bend, cut and install the tubing from the upstream of the valve to the T. 
  10. Install a tubing connector on the T, and another on the drip pot inlet. Connect these together with tubing 
  11. Attach tubing connectors to the outlet of the supply gas regulator and the supply side of the pilot and install the tubing.   
  12. The supply gas regulator cuts down the supply gas to the required 30PSI of the pilot. This is preset, so you won’t have to adjust it.  
  13. Attach tubing connectors to both the output of the pilot and the top of the valve bonnet. Cut, bend and install the tubing. Finish by installing a pressure gauge on the supply gas regulator. (Another gauge can be installed on one of the two sensing ports on the pilot. This is to see your sense pressure.) 
  14. The output of the pilot sends a pneumatic signal to the valve diaphragmclosing the valve. 

Note: For this package, you may be using a 30 HPG pilot instead of a high pressure pilot. For this configuration, the assembly will be the same, but the tubing lengths and angles will look different. 


Want to receive helpful resources like this directly in your inbox?

Subscribe to the Kimray Chronicle

Kyle Andrews serves as an Account Manager at Kimray. He provides Kimray product training and works with producers to identify project solutions.

Are You Finding What You Need?

Want More Industry Info?

Receive articles just like this in your inbox once a month. Subscribe to our Kimray Chronicle below.

Yes, Subscribe Me!